Fluid catalytic cracking (FCC) is the most important conversion process used in petroleum refineries. It is widely used to convert the high-boiling hydrocarbon fractions of petroleum crude oils into more valuable gasoline, olefinic gases and other products.
Cracking of petroleum hydrocarbons for conversion of heavy fractions into lighter fractions was originally done by thermal cracking which has been almost completely replaced by fluid catalytic cracking because it produces more gasoline with a higher octane rating. It also produces byproduct gases that are more olefinic, and hence more valuable, than those produced by thermal cracking.
The feedstock to an FCC is usually that portion of the crude oil that has an initial boiling point of 340 °Celsius (C) or higher at atmospheric pressure and an average molecular weight ranging from about 200 to 600 or higher. The FCC process vaporizes and breaks the long-chain molecules of the high-boiling hydrocarbon liquids into much shorter molecules by contacting the feedstock, at high temperature and moderate pressure, with a fluidized powdered catalyst.
In effect, refineries use fluid catalytic cracking to correct the imbalance between the market demand for gasoline and the excess of heavy, high boiling range products resulting from the distillation of crude oil.
As of 2006, FCC units were in operation at 400 petroleum refineries worldwide and about one-third of the crude oil refined in those refineries is processed in an FCC to produce high-octane gasoline and fuel oils. During 2007, the FCC units in the United States processed a total of 834,300,000 litres (5,300,000 barrels) per day of feedstock and FCC units worldwide processed about twice that amount.
Flow diagram and process description
The modern FCC units are all continuous processes which operate 24 hours a day for as much as two to three years between shutdowns for routine maintenance.
There are a number of different proprietary process designs that have been developed for modern FCC units. Each design is available under a license that must be purchased from the design developer by any petroleum refining company desiring to construct and operate an FCC of a given design.
Basically, there are two different configurations for an FCC unit: the "stacked" type where the reactor and the catalyst regenerator are contained in a single vessel with the reactor above the catalyst regenerator and the "side-by-side" type where the reactor and catalyst regenerator are in two separate vessels. These are the major FCC designers and licensors:
- Chicago Bridge & Iron (CBI) / Lummus
- ExxonMobil Research and Engineering (EMRE)
- Shell Global Solutions International
- Stone & Webster Engineering Corporation (SWECO) / Institut Francais du Petrole (IFP)
- Universal Oil Products (UOP)
- Kellogg Brown & Root (KBR)
Each of the proprietary design licensors claims to have unique features and advantages. A complete discussion of the relative advantages of each of the processes is well beyond the scope of this article. Suffice it to say that all of the licensors have designed and constructed FCC units that have operated quite satisfactorily.
The process flow diagram of a typical FCC unit, just below, is based on one of the above side-by-side configurations:
Reactor and regenerator
As depicted in the above diagram, the preheated high-boiling petroleum feedstock (at about 315 to 430 °C) consisting of long-chain hydrocarbon molecules is combined with recycle slurry oil from the bottom of the distillation column and injected into the catalyst riser where it is vaporized and cracked into smaller molecules of vapor by contact and mixing with the very hot powdered catalyst from the regenerator. All of the cracking reactions take place in the catalyst riser. The hydrocarbon vapors "fluidize" the powdered catalyst and the mixture of hydrocarbon vapors and catalyst flows upward to enter the reactor at a temperature of about 535 °C and a pressure of about 1.72 bar gauge.
The reactor is in fact merely a vessel in which the cracked product vapors are: (a) separated from the so-called spent catalyst by flowing through a set of two-stage cyclones within the reactor and (b) the spent catalyst flows downward through a steam stripping section to remove any hydrocarbon vapors before the spent catalyst returns to the catalyst regenerator. The flow of spent catalyst to the regenerator is regulated by a slide valve in the spent catalyst line.
Since the cracking reactions produce some carbonaceous material (referred to as coke) that deposits on the catalyst and very quickly reduces the catalyst reactivity, the catalyst is regenerated by burning off the deposited coke with air blown into the regenerator. The regenerator operates at a temperature of about 715 °C and a pressure of about 2.41 bar gauge. The combustion of the coke is exothermic and it produces a large amount of heat that is partially absorbed by the regenerated catalyst and provides the heat required for the vaporization of the feedstock and the endothermic cracking reactions that take place in the catalyst riser. For that reason, FCC units are often referred to as being "heat balanced".
The hot catalyst (at about 715 °C) leaving the regenerator flows into a catalyst withdrawal well where any entrained combustion flue gases are allowed to escape and flow back into the upper part to the regenerator. The flow of regenerated catalyst to the feedstock injection point below the catalyst riser is regulated by a slide valve in the regenerated catalyst line. The hot flue gas exits the regenerator after passing through multiple sets of two-stage cyclones that remove entrained catalyst from the flue gas.
The amount of catalyst circulating between the regenerator and the reactor amounts to about five kilograms (k)g per kg of feedstock which is equivalent to about 4.66 kg per litre of feedstock. Thus, an FCC unit processing 12,000,000 litres/day (75,000 barrels/day) will circulate about 55,900 metric tons per day of catalyst.
The reaction product vapors (at 535 °C and a pressure of 1.72 bar gauge) flow from the top of the reactor to the bottom section of the distillation column (commonly referred to as the main fractionator) where they are distilled into the FCC end products of cracked naphtha, fuel oil and offgas. After further processing for removal of sulfur compounds, the cracked naphtha becomes a high-octane component of the refinery's blended gasolines.
The main fractionator offgas is sent to what is called a gas recovery unit where it is separated into butanes and butylenes, propane and propylene, and lower molecular weight gases (hydrogen, methane, ethylene and ethane). Some FCC gas recovery units may also separate out part of the ethane and ethylene.
Although the flow diagram above depicts the main fractionator as having only one sidecut stripper and one fuel oil product, many FCC main fractionators have two sidecut strippers and produce a light fuel oil and a heavy fuel oil. Likewise, many FCC main fractionators produce a light cracked naphtha and a heavy cracked naphtha. The terminology light and heavy in this context refers to the product boiling ranges, with light products having a lower boiling range than heavy products.
The bottom product oil from the main fractionator contains catalyst fines which were not removed by the cyclones in the top of the reactor. For that reason, the bottom product oil is referred to as a slurry oil. Part of that slurry oil is recycled back into the main fractionator above the entry point of the hot reaction product vapors so as to cool and partially condense the reaction product vapors as they enter the main fractionator. The remainder of the slurry oil is pumped through a slurry settler. The bottom oil from the slurry settler contains most of the slurry oil catalyst particles and is recycled back into the catalyst riser by combining it with the FCC feedstock oil. The so-called clarified slurry oil is withdrawn from the top of slurry settler for use elsewhere in the refinery or as a heavy fuel oil blending component.
Regenerator flue gas
Depending on the choice of FCC design, the combustion in the regenerator of the coke on the spent catalyst may or may not be complete combustion to carbon dioxide (CO2). The combustion air flow is controlled so as to provide the desired ratio of carbon monoxide (CO) to carbon dioxide for each specific FCC design.
In the design shown in the above flow diagram, the coke has only been partially combusted to CO2. The combustion flue gas (containing CO and CO2) at 715 °C and at a pressure of 2.41 bar gauge is routed through a secondary catalyst separator containing swirl tubes designed to remove 70 to 90 percent of the catalyst fines in the flue gas leaving the regenerator. This is required to prevent erosion damage to the blades in the turbo-expander that the flue gas is next routed through.
The expansion of flue gas through a turbo-expander provides sufficient power to drive the regenerator's combustion air compressor. The electrical motor-generator can consume or produce electrical power. If the expansion of the flue gas does not provide enough power to drive the air compressor, the electric motor-generator provides the needed additional power. If the flue gas expansion provides more power than needed to drive the air compressor, than the electric motor-generator converts the excess power into electric power and exports it to the refinery's electrical system.
The expanded flue gas is then routed through a steam-generating boiler (referred to as a CO boiler) where the carbon monoxide in the flue gas is burned as fuel to provide steam for use in the refinery as well as to comply with any applicable environmental regulatory limits on carbon monoxide emissions.
The flue gas is finally processed through an electrostatic precipitator (ESP) that removes residual particulate matter to comply with any applicable environmental regulations regarding particulate emissions. The ESP removes particulates in the size range of two to 20 microns (i.e., micrometres) from the flue gas.
The steam turbine in the flue gas processing system (shown in the above diagram) is used to drive the regenerator's combustion air compressor during start-ups of the FCC unit until there is sufficient combustion flue gas to take over that task.
Before delving into the chemistry involved in catalytic cracking, it will be helpful to briefly discuss the composition of petroleum crude oil.
Constituents of petroleum crude oil
Petroleum crude oil consists primarily of a mixture of hydrocarbons with small amounts of other organic compounds containing sulfur, nitrogen and oxygen. The crude oil also contains small amounts of metals such as copper, iron, nickel and vanadium.
The elemental composition ranges of crude oil are summarized in the adjacent table and the hydrocarbons in the crude oil can be classified into three types:
- Paraffins or alkanes: saturated straight-chain or branched hydrocarbons, without any ring structures.
- Naphthenes or cycloalkanes: saturated hydrocarbons having one or more ring structures with one or more paraffinic side-chains.
- Aromatics: hydrocarbons having one or more unsaturated ring structures such as benzene or unsaturated polycyclic ring structures such as naphthalene or phenanthrene, any of which may also have one or more paraffinic side-chains
The chemistry of cracking
In plain language, the fluid catalytic cracking process breaks large hydrocarbon molecules into smaller molecules by contacting them with a powdered catalyst at a high temperature and moderate pressure which first vaporizes the hydrocarbons and then breaks them. The cracking reactions occur in the vapor phase and start immediately when the feedstock is vaporized in the catalyst riser.
The adjacent diagram is a very simplified schematic that exemplifies how the process breaks high boiling, straight-chain alkane (paraffin) hydrocarbons into smaller straight-chain alkanes as well as branched-chain alkanes, branched alkenes (olefins) and cycloalkanes (naphthenes). The breaking of the large hydrocarbon molecules into smaller molecules is more technically referred to by organic chemists as scission of the carbon-to-carbon bonds.
As depicted in the adjacent schematic, some of the smaller alkanes are then broken and converted into even smaller alkenes and branched alkenes such as the gases ethylene, propylene, butylenes and isobutylenes. Those olefinic gases are valuable for use as petrochemical feedstocks. The propylene, butylenes and isobutylenes are also valuable feedstocks for certain petroleum refining processes that convert them into high-octane gasoline blending components.
As also depicted in the schematic, the cycloalkanes (naphthenes) formed by the initial breakup of the large molecules are further converted to aromatics such as benzene, toluene and xylenes which boil in the gasoline boiling range and have much higher octane ratings than alkanes.
By no means does the schematic include all the chemistry of the primary and secondary reactions taking place in the fluid catalytic process. There are a great many other reactions involved. However, a full discussion of the highly technical details of the various catalytic cracking reactions is beyond the scope of this article and can be found in the technical literature.
Modern FCC catalysts are fine powders with a bulk density of 0.80 to 0.96 g/cc and having a particle size distribution ranging from 10 to 150 μm and an average particle size of 60 to 100 μm.
The design and operation of an FCC unit is largely dependent upon the chemical and physical properties of the catalyst. The desirable properties of an FCC catalyst are:
- Good stability to high temperature and to steam
- High activity
- Large pore sizes
- Good resistance to attrition
- Low coke production
A modern FCC catalyst has four major components: crystalline zeolite, matrix, binder and filler. Zeolite is the primary active component and can range from about 15 to 50 weight percent of the catalyst. The zeolite used in FCC catalysts is referred to faujasite or as Type Y and is comprised of silica and alumina tetrahedra with each tetrahedron having either an aluminum or a silicon atom at the center and four oxygen atoms at the corners. It is a molecular sieve with a distinctive lattice structure that allows only a certain size range of hydrocarbon molecules to enter the lattice. In general, the zeolite does not allow molecules larger than eight to ten nanometers (i.e., 80 to 100 angstroms) to enter the lattice.
The catalytic sites in the zeolite are strong acids (equivalent to 90% sulfuric acid) and provide most of the catalyst activity. The acidic sites are provided by the alumina tetrahedra. The aluminum atom at the center of each alumina tetrahedra is at a +3 oxidation state surrounded by four oxygen atoms at the corners which are shared by the neighboring tetrahedra. Thus, the net charge of the alumina tetrahedra is -1 which is balanced by a sodium ion during the production of the catalyst. The sodium ion is later replaced by an ammonium ion which is vaporized when the catalyst is subsequently dried, resulting in the formation of Lewis and Brønsted acidic sites. In some FCC catalysts, the Brønsted sites may be later replaced by rare earth metals such as cerium and lanthanum to provide alternative activity and stability levels.
The matrix component of an FCC catalyst contains amorphous alumina which also provides catalytic activity sites and in larger pores that allows entry for larger molecules than does the zeolite. That enables the cracking of higher-boiling, larger feedstock molecules than are cracked by the zeolite.
The binder and filler components provide the physical strength and integrity of the catalyst. The binder is usually a silica solution and the filler is usually a clay (kaolin).
Nickel, vanadium, iron, copper and other metal contaminants, present in FCC feedstocks in the parts per million range, all have detrimental effects on the catalyst activity and performance. Nickel and vanadium are particularly troublesome. There are a number of methods for mitigating the effects of the contaminant metals:
- Avoid feedstocks with high metals content: This seriously hampers a refinery's flexibility to process various crude oils or purchased FCC feedstocks.
- Feedstock feed pretreatment: Hydrodesulfurization of the FCC feedstock removes some of the metals and also reduces the sulfur content of the FCC products. However, this is quite a costly option.
- Increasing fresh catalyst addition: All FCC units withdraw some of the circulating equilibrium catalyst as spent catalyst and replaces it with fresh catalyst in order to maintain a desired level of activity. Increasing the rate of such exchange lowers the level of metals in the circulating equilibrium catalyst, but this is also quite a costly option.
- Demetallization: The commercial proprietary Demet Process removes nickel and vanadium from the withdrawn spent catalyst. The nickel and vanadium are converted to chlorides which are then washed out of the catalyst. After drying, the demetallized catalyst is recycled into the circulating catalyst. Removals of about 95 percent nickel and 67 to 85 percent vanadium have been reported. Despite that, the use of the Demet process has not become widespread, perhaps because of the high capital expenditure required.
- Metals passivation: Certain materials can be used as additives which can be impregnated into the catalyst or added to the FCC feedstock in the form of metal-organic compounds. Such materials react with the metal contaminants and passivate the contaminants by forming less harmful compounds that remain on the catalyst. For example, antimony and bismuth are effective in passivating nickel and tin is effective in passivating vanadium. A number of proprietary passivation processes are available and fairly widely used.
The first commercial use of catalytic cracking occurred in 1915 when Almer M. McAfee of the Gulf Refining Company developed a batch process using aluminum chloride (a Friedel Crafts catalyst known since 1877) to catalytically crack heavy petroleum oils. However, the prohibitive cost of the catalyst prevented the widespread use of McAfee's process at that time.
In 1922, a French mechanical engineer named Eugene Jules Houdry and a French pharmacist named E.A. Prudhomme set up a laboratory near Paris to develop a catalytic process for converting lignite coal to gasoline. Supported by the French government, they built a small demonstration plant in 1929 that processed about 60 tons per day of lignite coal. The results indicated that the process was not economically viable and it was subsequently shutdown.
Houdry had found that Fuller's Earth, a clay mineral containing aluminosilicate (Al2SiO6, could convert oil derived from the lignite to gasoline. He then began to study the catalysis of petroleum oils and had some success in converting vaporized petroleum oil to gasoline. In 1930, the Vacuum Oil Company invited him to come to the United States and he moved his laboratory to Paulsboro, New Jersey.
In 1931, the Vacuum Oil Company merged with Standard Oil of New York (Socony) to form the Socony-Vacuum Oil Company. In 1933, a small Houdry process unit processing 200 barrels per day (32,000 litres per day) of petroleum oil. Because of the economic depression of the early 1930's, Socony-Vacuum was no longer able to support Houdry's work and gave him permission to seek help elsewhere.
In 1933, Houdry and Socony-Vacuum joined with Sun Oil Company in developing the Houdry process. Three years later, in 1936, Socony-Vacuum converted an older thermal cracking unit in their Paulsboro refinery in New Jersey to a small demonstration unit using the Houdry process to catalytically crack 2,000 barrels per day (318,000 litres per day) of petroleum oil.
In 1937, Sun Oil began operation of a new Houdry unit processing 12,000 barrels per day (2,390,000 litres per day) at their Marcus Hook refinery in Pennsylvania. The Houdry process at that time used reactors with a fixed bed of catalyst and was a semi-batch operation involving multiple reactors with some of the reactors in operation while other reactors were in various stages of regenerating the catalyst. Motor-driven valves were used to switch the reactors between online operation and offline regeneration and a cycle timer managed the switching. Almost 50 percent of the cracked product was gasoline as compared with about 25 percent from the thermal cracking processes.
By 1938, when the Houdry process was publicly announced, Socony-Vacuum had eight additional units under construction. Licensing the process to other companies also began and by 1940 there were 14 Houdry units in operation processing 140,000 barrels per day (22,300,000 litres per day).
The next major step was to develop a continuous process rather than the semi-batch Houdry process. That step was implemented by advent of the moving-bed process known as the Thermafor Catalytic Cracking (TCC) process which used a bucket conveyor-elevator to move the catalyst from the regeneration kiln to the separate reactor section. A small demonstration TCC unit was built in Socony-Vacuum's Paulsboro refinery in 1941 and operated successfully. Then a full-scale commercial TCC unit processing 10,000 barrels per day (1,590,000 litres per day) began operation in 1943 at the Beaumont, Texas refinery of Magnolia Oil Company, an affiliate of Socony-Vacuum. By the end of World War II in 1945, the processing capacity of the TCC units in operation was about 300,000 barrels per day (47,700,000 litres per day).
It is said that the Houdry and TCC units were a major factor in the winning of World War II by supplying the high-octane gasoline needed by the air forces of Great Britain and the United States.
In the years immediately after World War II, the Houdriflow process and the air-lift TCC process were developed as improved variations on the moving-bed theme. Just like Houdry's fixed-bed reactors, the moving-bed designs were prime examples of good engineering by developing a method of continuously moving the catalyst between the reactor and regeneration sections.
The fluid catalytic cracking process had first been investigated in the 1920s by Standard Oil of New Jersey, but research on it was abandoned during the economic depression years of 1929 to 1939. In 1938, when the success of Houdry’s process had become apparent, Standard Oil of New Jersey resumed the project as part of a consortium of that include five oil companies (Standard Oil of New Jersey, Standard Oil of Indiana, Anglo-Iranian Oil, Texas Oil and Dutch Shell), two engineering-construction companies (M.W. Kellogg and Universal Oil Products) and a German chemical company (I.G. Farben). The consortium was called Catalytic Research Associates (CRA) and its purpose was to develop a catalytic cracking process which would not impinge on Houdry's patents.
Chemical engineering professors Warren K. Lewis and Edwin R. Gilliland of the Massachusetts Institute of Technology (MIT) suggested to the CRA researchers that a low velocity gas flow through a powder might "lift" it enough to cause it to flow in a manner similar to a liquid. Focused on that idea of a fluidized catalyst, researchers Donald Campbell, Homer Martin, Eger Murphree and Charles Tyson of the Standard Oil of New Jersey (now Exxon-Mobil Company) developed the first fluidized catalytic cracking unit. Their U.S. Patent No. 2,451,804, "A Method of and Apparatus for Contacting Solids and Gases", describes their milestone invention. Based on their work, M. W. Kellogg Company constructed a large pilot plant in the Baton Rouge, Louisiana refinery of the Standard Oil of New Jersey. The pilot plant began operation in May of 1940.
Based on the success of the pilot plant, the first commercial fluid catalytic cracking plant (known as the Model I FCC) began processing 13,000 barrels per day (2,070,000 litres per day) of petroleum oil in the Baton Rouge refinery on May 25, 1942, just four years after the CRA consortium was formed and in the midst of World War II. A little more than a month later, in July 1942, it was processing 17,000 barrels per day (2,700,000 litres per day). In 1963, that first Model I FCC unit was shut down after 21 years of operation and subsequently dismantled.
In the many decades since the Model I FCC unit began operation, the fixed bed Houdry units have all been shut down as have most of the moving bed units (such as the TCC units) while hundreds of FCC units have been built. During those decades, many improved FCC designs have evolved and cracking catalysts have been greatly improved, but the modern FCC units are essentially the same as that first Model I FCC unit.
Note: All of the refinery and company names in this history section (with the exception of Universal Oil Products) have changed over time by mergers and buyouts. Some have changed a number of times.
- James H. Gary and Glenn E. Handwerk (2001), Petroleum Refining: Technology and Economics, 4th Edition, CRC Press, ISBN 0-8247-0482-7.
- James. G. Speight (2006), The Chemistry and Technology of Petroleum, 4th Edition, CRC Press, ISBN 0-8493-9067-2.
- Reza Sadeghbeigi (2000), Fluid Catalytic Cracking Handbook, 2nd Edition, Gulf Publishing, ISBN 0-88415-289-8
- Editors: David S.J. Jones and Peter P. Pujado (2006), Handbook of Petroleum Processing, 1st Edition, Springer, ISBN 1-4020-2819-9.
- U.S. Downstream Processing of Fresh Feed Input by Catalytic Cracking Units, Energy Information Administration, U.S. Dept. of Energy
- Editorial Staff, "Refining Processes", Hydrocarbon Processing, November 2002, pp. 108-112, ISSN 0887-0284.
- Alex C. Hoffnab and Lewis E. Stein (2002), Gas Cyclones and Swirl Tubes: Principles, Design and Operation, 1st Edition Springer, ISBN 3-540-43326-0..
- Editors: Jessica Elzea Kogel, Nikhil C. Trivedi, James M. Barber and Stanley T. Krukowsk (2006), Industrial Minerals & Rocks: Commodities, Markets and Uses 7th Edition, Society of Mining, Metallurgy and Exploration, ISBN 0-87335-233-5.
- Wen-Ching Yang (2003), Handbook of Fluidization and Fluid Particle Systems, CRC Press, ISBN 0-8247-0259-X.
- Passivate Vanadium on FCC Catalysts for Improved Refinery Profitability, 1997 Annual National Petrochemical and Refiners Association Meeting.
- Julius Scherzer (1990), Octane-enhancing Zeolitic FCC Catalysts: Scientific and Technical Aspects, CRC Press, ISBN 0-8247-8399-9.
- Pioneer of Catalytic Cracking: Almer McAfee at Gulf Oil, From the website of the North American Catalysis Society.
- Tim Palucka, "The Wizard of Octane: Eugene Houdry", Invention & Technology, Vol. 20, Issue 3, Winter 2005.
- Amos A. Avidan, Michael Edwards and Hartley Owen, "Innovative Improvements Highlight FCC's Past and Future", Oil & Gas Journal, Vol.88, Issue 2, January 8, 1990.
- The Houdry Process From the website of the American Chemical Society.
- The Fluid Bed Reactor, From the website of the American Chemical Society.