In physics, a force is the influence that one physical object has on another that causes (unless offset by an equal and opposite force) a change in motion. Forces are commonly thought of as a things that "push" or "pull" an object. A force has both magnitude and direction properties, making it a vector quantity.
Modern undertanding of how force works is rooted in the mathematical "laws of motion" developed by Isaac Newton approximately 300 years ago.
Newton's formulation states that the net force on a body is equal to its change in momentum with time. For a body with fixed mass, this becomes the a direct measure of acceleration; the change in velocity over time. Because velocity is a vector, it can change in two ways: a change in magnitude and/or a change in direction.
Forces which do not act uniformly on all parts of a body will also cause mechanical stresses, which causes deformation of matter. While mechanical stress can remain embedded in a solid object, gradually deforming it, mechanical stress in a fluid determines changes in its pressure and volume.
There are four "fundamental" forces in nature: gravity, electromangetic, strong, and weak forces. In day-to-day experience, these fundamental forces manifest themselves in a way that are labeled as normal, friction, tension, torque, elastic, centripetal, or by other words. These are often refered to a "non fundamental" forces.
In physics, the consideration of forces acting on objects is refered as "mechanics." The branch of mechanics that deals with stationary objects is known as "statics," while the branch of mechanics that deals with moving objects is known as "dynamics." In constrast, the consideration of the motion of objects without reference to the cause of that motion is known as "kinematics."
Classical mechanics, which handles most objects much larger than atoms much slower than the speed of light, is rooted in Newton's laws of motion. At speeds close to that of light, Einstein's special and general theories of relativity become significant and eventually dominant over classical formulations of mechanics. Quantum mechanics, developed in the 1920s, applies at atomic and subatomic scales.
Related concepts include thrust - any force which increases the velocity of the object, drag - any force which decreases the velocity of any object, and torque - the tendency of a force to cause changes in rotational speed about an axis.
Since antiquity, the concept of force has been recognized as integral to the functioning of simple machines ( levers, wheels and axles, pulleys, inclined planes, wedges, screws). The mechanical advantage given by a simple machine allowed for less force to be used in exchange for that force acting over a greater distance. Analysis of the characteristics of forces ultimately culminated in the work of Archimedes (287 BC – 212 BC) who was especially famous for formulating a treatment of buoyant forces inherent in fluids.
Aristotle (384 BC – 322 BC) provided a philosophical discussion of the concept of a force as an integral part of Aristotelian cosmology. In Aristotle's view, the natural world held four elements (earth, water, air, fire) that existed in "natural states". Aristotle believed that it was the natural state of objects with mass on Earth, such as the elements water and earth, to be motionless on the ground and that they tended towards that state if left alone. He distinguished between the innate tendency of objects to find their "natural place" (e.g., for heavy bodies to fall), which led to "natural motion", and unnatural or forced motion, which required continued application of a force.
This theory, based on the everyday experience of how objects move, such as the constant application of a force needed to keep a cart moving, had conceptual trouble accounting for the behavior of projectiles, such as the flight of arrows. The place where forces were applied to projectiles was only at the start of the flight, and while the projectile sailed through the air, no discernible force acts on it. Aristotle was aware of this problem and proposed that the air displaced through the projectile's path provided the needed force to continue the projectile moving. This explanation demands that air is needed for projectiles and that, for example, in a vacuum, no projectile would move after the initial push. Additional problems with the explanation include the fact that air resists the motion of the projectiles.
Aristotelian physics began facing criticism in Medieval science, first by John Philoponus (490–570 AD) and then by other physicists from the 11th century, when Avicenna's The Book of Healing introduced an alternative theory of mayl, where motion is a result of an inclination (mayl) transferred to the projectile by the thrower, projectile motion in a vacuum does not cease, and inclination is a permanent force whose effect is dissipated by external forces such as air resistance. Avicenna (c. 980 - 1037) also developed the concept of momentum, referring to mayl as being proportional to weight times velocity.
The shortcomings of Aristotelian physics would not be fully corrected until the seventeenth century work of Galileo Galilei (1564 – 1642), who was influenced by the late Medieval idea that objects in forced motion carried an innate force of impetus. Galileo constructed an experiment in which stones and cannonballs were both rolled down an incline to disprove the Aristotelian theory of motion early in the seventeenth century. He showed that the bodies were accelerated by gravity to an extent which was independent of their mass and argued that objects retain their velocity unless acted on by a force, for example friction. Galileo realized that simple velocity addition demands that the concept of an "absolute rest frame" did not exist. Galileo concluded that motion in a constant velocity was completely equivalent to rest. This was contrary to Aristotle's notion of a "natural state" of rest that objects with mass naturally approached.
Simple experiments showed that Galileo's understanding of the equivalence of constant velocity and rest to be correct. For example, if a mariner dropped a cannonball from the crow's nest of a ship moving at a constant velocity, Aristotelian physics would have the cannonball fall straight down while the ship moved beneath it. Thus, in an Aristotelian universe, the falling cannonball would land behind the foot of the mast of a moving ship. However, when this experiment is actually conducted, the cannonball always falls at the foot of the mast, as if the cannonball knows to travel with the ship despite being separated from it. Since there is no forward horizontal force being applied on the cannonball as it falls, the only conclusion left is that the cannonball continues to move with the same velocity as the boat as it falls. Thus, no force is required to keep the cannonball moving at the constant forward velocity.
Classical "Newtonian" mechanics
Sir Isaac Newton (1642–1727) sought to describe the motion of all objects using the concepts of inertia and force, and in doing so, he found that they obey certain conservation laws. In 1687, Newton went on to publish his thesis "Philosophiae Naturalis Principia Mathematica" In this work, Newton set out three laws of motion that, to this day, are the way forces are described in physics.
Newton's first law
Newton's first law of motion states that objects continue to move in a state of constant velocity unless acted upon by an external net force or "resultant force". This law is an extension of Galileo's insight that constant velocity was associated with a lack of net force.
Equilibrium occurs when the resultant force acting on a point particle is zero (that is, the vector sum of all forces is zero). When dealing with an extense body, it is also necessary that the net torque in it is zero. There are two kinds of equilibrium: static equilibrium when the body is at rest and dynamic equilibrium when the body is in motion
- The simplest case of static equilibrium occurs when two forces are equal in magnitude but opposite in direction (see Figure right). For example , an object on a level surface is pulled (attracted) downward toward the center of the Earth by the force of gravity. At the same time, surface forces resist the downward force with equal upward force (called the normal force). The situation is one of zero net force and no acceleration. Pushing against an object on a frictional surface can result in a situation where the object does not move because the applied force is opposed by static friction, generated between the object and the table surface. For a situation with no movement, the static friction force exactly balances the applied force resulting in no acceleration. The static friction increases or decreases in response to the applied force up to an upper limit determined by the characteristics of the contact between the surface and the object. A static equilibrium between two forces is the most usual way of measuring forces, using simple devices such as weighing scales and spring balances. For example, an object suspended on a vertical spring scale experiences the force of gravity acting on the object balanced by a force applied by the "spring reaction force" which equals object's weight. Using such tools, some quantitative force laws were discovered: that the force of gravity is proportional to volume for objects of constant density (widely exploited for millennia to define standard weights); Archimedes' principle for buoyancy; Archimedes' analysis of the lever; Boyle's law for gas pressure; and Hooke's law for springs. These were all formulated and experimentally verified before Newton expounded his laws of motion.
Force as a Vector
Forces act in a particular direction and have sizes dependent upon how strong the push or pull is. Because of these characteristics, forces are classified as "vector quantities". This means that forces follow a different set of mathematical rules than physical quantities that do not have direction (denoted scalar quantities). For example, when determining what happens when two forces act on the same object, it is necessary to know both the magnitude and the direction of both forces to calculate the result. If both of these pieces of information are not known for each force, the situation is ambiguous. For example, if one knows that two people are pulling on the same rope with known magnitudes of force but you do not know which direction either person is pulling, it is impossible to determine what the acceleration of the rope will be. The two people could be pulling against each other as in tug of war or the two people could be pulling in the same direction. In this simple one-dimensional example, without knowing the direction of the forces it is impossible to decide whether the net force is the result of adding the two force magnitudes or subtracting one from the other. Associating forces with vectors avoids such problems.
Historically, forces were first quantitatively investigated in conditions of static equilibrium where several forces canceled each other out. Such experiments demonstrate the crucial properties that forces are additive vector quantities: they have magnitude and direction. When two forces act on an object, the resulting force, the resultant, can be determined by following the parallelogram rule of vector addition: the addition of two vectors represented by sides of a parallelogram, gives an equivalent resultant vector which is equal in magnitude and direction to the transversal of the parallelogram. The magnitude of the resultant varies from the difference of the magnitudes of the two forces to their sum, depending on the angle between their lines of action.Free-body diagrams can be used as a convenient way to keep track of forces acting on a system. Ideally, these diagrams are drawn with the angles and relative magnitudes of the force vectors preserved so that graphical vector addition can be done to determine the resultant.
As well as being added, forces can also be resolved into independent components at right angles to each other. A horizontal force pointing northeast can therefore be split into two forces, one pointing north, and one pointing east. Or, as in the Figure above of the block on an inclined plane, resolved into a force parallel to the plane and into the plane. Summing these component forces using vector addition yields the original force. Resolving force vectors into components of a set of basis vectors is often a more mathematically clean way to describe forces than using magnitudes and directions. This is because, for orthogonal components, the components of the vector sum are uniquely determined by the scalar addition of the components of the individual vectors. Orthogonal components are independent of each other because forces acting at ninety degrees to each other have no effect on the magnitude or direction of the other. Choosing a set of orthogonal basis vectors is often done by considering what set of basis vectors will make the mathematics most convenient. Choosing a basis vector that is in the same direction as one of the forces is desirable, since that force would then have only one non-zero component. Orthogonal force vectors can be three-dimensional with the third component being at right-angles to the other two.
- A simple case of dynamical equilibrium occurs in constant velocity motion across a surface with kinetic friction. In such a situation, a force is applied in the direction of motion while the kinetic friction force exactly opposes the applied force. This results in a net zero force, but since the object started with a non-zero velocity, it continues to move with a non-zero velocity. Aristotle misinterpreted this motion as being caused by the applied force. However, when kinetic friction is taken into consideration it is clear that there is no net force causing constant velocity motion.
Newton proposed that every object with mass has an innate inertia that functions as the fundamental equilibrium "natural state" in place of the Aristotelian idea of the "natural state of rest". That is, the first law contradicts the intuitive Aristotelian belief that a net force is required to keep an object moving with constant velocity.
By making rest physically indistinguishable from non-zero constant velocity, Newton's first law directly connects inertia with the concept of relative velocities. Specifically, in systems where objects are moving with different velocities, it is impossible to determine which object is "in motion" and which object is "at rest". In other words, to phrase matters more technically, the laws of physics are the same in every inertial frame of reference, that is, in all frames related by a Galilean transformation.
For example, while traveling in a moving vehicle at a constant velocity, the laws of physics do not change from being at rest. A person can throw a ball straight up in the air and catch it as it falls down without worrying about applying a force in the direction the vehicle is moving. This is true even though another person who is observing the moving vehicle pass by also observes the ball follow a curving parabolic path in the same direction as the motion of the vehicle. It is the inertia of the ba
ll associated with its constant velocity in the direction of the vehicle's motion that ensures the ball continues to move forward even as it is thrown up and falls back down. From the perspective of the person in the car, the vehicle and every thing inside of it is at rest: It is the outside world that is moving with a constant speed in the opposite direction. Since there is no experiment that can distinguish whether it is the vehicle that is at rest or the outside world that is at rest, the two situations are considered to be physically indistinguishable. Inertia therefore applies equally well to constant velocity motion as it does to rest.
The concept of inertia can be further generalized to explain the tendency of objects to continue in many different forms of constant motion, even those that are not strictly constant velocity. The rotational inertia of planet Earth is what fixes the constancy of the length of a day and the length of a year.
Albert Einstein extended the principle of inertia further when he explained that reference frames subject to constant acceleration, such as those free-falling toward a gravitating object, were physically equivalent to inertial reference frames. This is why, for example, astronauts experience weightlessness when in free-fall orbit around the Earth, and why Newton's Laws of Motion are more easily discernible in such environments. If an astronaut places an object with mass in mid-air next to herself, it will remain stationary with respect to the astronaut due to its inertia. This is the same thing that would occur if the astronaut and the object were in intergalactic space with no net force of gravity acting on their shared reference frame. This principle of equivalence was one of the foundational underpinnings for the development of the general theory of relativity.
Newton's second law
A modern statement of Newton's second law is a vector differential equation:
where p is the momentum of the system, and F is the net (vector sum) force. In equilibrium, there is zero net force by definition, but (balanced) forces may be present nevertheless. In contrast, the second law states an unbalanced force acting on an object will result in the object's momentum changing over time.
By the definition of momentum,
where m is the mass and v is the velocity.
The product rule shows that:
For closed systems (systems of constant total mass), the time derivative of mass is zero and the equation becomes
By substituting the definition of acceleration, the algebraic version of this common simplification of Newton's second law is derived:
Newton's second law (although Newton never explicitly stated the formula in the reduced form above) asserts the proportionality of acceleration and mass to force. It is sometimes called the "second most famous formula in physics" (after E=mc2).
Accelerations can be defined through kinematic measurements. However, while kinematics are well-described through reference frame analysis in advanced physics, there are still deep questions that remain as to what is the proper definition of mass. General relativity offers an equivalence between space-time and mass, but lacking a coherent theory of quantum gravity, it is unclear as to how or whether this connection is relevant on microscales. With some justification, Newton's second law can be taken as a quantitative definition of mass by writing the law as an equality; the relative units of force and mass then are fixed.
The use of Newton's second law as a definition of force has been disparaged in some of the more rigorous textbooks, because it is essentially a mathematical truism. The equality between the abstract idea of a "force" and the abstract idea of a "changing momentum vector" ultimately has no observational significance because one cannot be defined without simultaneously defining the other. What a "force" or "changing momentum" is must either be referred to an intuitive understanding of our direct perception, or be defined implicitly through a set of self-consistent mathematical formulas. Notable physicists, philosophers and mathematicians who have sought a more explicit definition of the concept of "force" include Ernst Mach, Clifford Truesdell and Walter Noll.
Newton's second law can be used to measure the strength of forces. For instance, knowledge of the masses of planets along with the accelerations of their orbits allows scientists to calculate the gravitational forces on planets.
Newton's third law
Newton's third law is a result of applying symmetry to situations where forces can be attributed to the presence of different objects. For any two objects (call them 1 and 2), Newton's third law states that any force that is applied to object 1 due to the action of object 2 is automatically accompanied by a force applied to object 2 due to the action of object 1
Image:Force equation 6.png
This law implies that forces always occur in action-and-reaction pairs. If object 1 and object 2 are considered to be in the same system, then the net force on the system due to the interactions between objects 1 and 2 is zero since
Image:Force equation 7.png or Image:Force equation 8.png
This means that in a closed system where there is no net external force, linear momentum of the system does not change with time. This is know as the conservation of linear momentum. Using the similar arguments, it is possible to generalizing this to a system of an arbitrary number of particles. This shows that exchanging momentum between constituent objects will not affect the net momentum of a system. In general, as long as all forces are due to the interaction of objects with mass, it is possible to define a system such that net momentum is never lost nor gained.
All the forces in the universe are based on four fundamental forces. The strong and weak forces act only at very short distances, and are responsible for the interactions between subatomic particles including nucleons and compound nuclei. The electromagnetic force acts between electric charges and the gravitational force acts between masses. All other forces are based on the existence of the four fundamental interactions. For example, friction is a manifestation of the electromagnetic force acting between the atoms of two surfaces, and the Pauli Exclusion Principle, which does not allow atoms to pass through each other. The forces in springs, modeled by Hooke's law, are also the result of electromagnetic forces and the Exclusion Principle acting together to return the object to its equilibrium position. Centrifugal forces are acceleration forces which arise simply from the acceleration of rotating frames of reference.
The development of fundamental theories for forces proceeded along the lines of unification of disparate ideas. For example, Isaac Newton unified the force responsible for objects falling at the surface of the Earth with the force responsible for the orbits of celestial mechanics in his universal theory of gravitation. Michael Faraday and James Clerk Maxwell demonstrated that electric and magnetic forces were unified through one consistent theory of electromagnetism. In the twentieth century, the development of quantum mechanics led to a modern understanding that the first three fundamental forces (all except gravity) are manifestations of matter (fermions) interacting by exchanging virtual particles called gauge bosons. This standard model of particle physics posits a similarity between the forces and led scientists to predict the unification of the weak and electromagnetic forces in electroweak theory subsequently confirmed by observation. The complete formulation of the standard model predicts an as yet unobserved Higgs mechanism, but observations such as neutrino oscillations indicate that the standard model is incomplete. A grand unified theory allowing for the combination of the electroweak interaction with the strong force is held out as a possibility with candidate theories such as supersymmetry proposed to accommodate some of the outstanding unsolved problems in physics. Physicists are still attempting to develop self-consistent unification models that would combine all four fundamental interactions into a theory of everything. Einstein tried and failed at this endeavor, but currently the most popular approach to answering this question is string theory.
What we now call gravity was not identified as a universal force until the work of Isaac Newton. Before Newton, the tendency for objects to fall towards the Earth was not understood to be related to the motions of celestial objects. Galileo was instrumental in describing the characteristics of falling objects by determining that the acceleration of every object in free-fall was constant and independent of the mass of the object. Today, this acceleration due to gravity towards the surface of the Earth is usually designated as g and has a magnitude of about 9.81 meters per second squared (this measurement is taken from sea level and may vary depending on location), and points toward the center of the Earth. This observation means that the force of gravity on an object at the Earth's surface is directly proportional to the object's mass. Thus an object that has a mass of m will experience a force:
Image:Force equation 18.png
In free-fall, this force is unopposed and therefore the net force on the object is its weight. For objects not in free-fall, the force of gravity is opposed by the reactions of their supports. For example, a person standing on the ground experiences zero net force, since his weight is balanced by a normal force exerted by the ground.
Newton's contribution to gravitational theory was to unify the motions of heavenly bodies, which Aristotle had assumed were in a natural state of constant motion, with falling motion observed on the Earth. He proposed a law of gravity that could account for the celestial motions that had been described earlier using Kepler's Laws of Planetary Motion.
Newton came to realize that the effects of gravity might be observed in different ways at larger distances. In particular, Newton determined that the acceleration of the Moon around the Earth could be ascribed to the same force of gravity if the acceleration due to gravity decreased as an inverse square law. Further, Newton realized that the acceleration due to gravity is proportional to the mass of the attracting body. Combining these ideas gives a formula that relates the mass Mo and the radius Ro of the Earth to the gravitational acceleration:
Image:Force equation 19.png
where the vector direction is given by r, the unit vector directed outward from the center of the Earth.
In this equation, a dimensional constant G is used to describe the relative strength of gravity. This constant has come to be known as Newton's Universal Gravitation Constant, though its value was unknown in Newton's lifetime. Not until 1798 was Henry Cavendish able to make the first measurement of G using a torsion balance; this was widely reported in the press as a measurement of the mass of the Earth since knowing the G could allow one to solve for the Earth's mass given the above equation. Newton, however, realized that since all celestial bodies followed the same laws of motion, his law of gravity had to be universal. Succinctly stated, Newton's Law of Gravitation states that the force on a spherical object of mass m1 due to the gravitational pull of mass m2 is
Image:Force equation 20.png
where r is the distance between the two objects' centers of mass and r(hat) is the unit vector pointed in the direction away from the center of the first object toward the center of the second object.
This formula was powerful enough to stand as the basis for all subsequent descriptions of motion within the solar system until the twentieth century. During that time, sophisticated methods of perturbation analysis were invented to calculate the deviations of orbits due to the influence of multiple bodies on a planet, moon, comet, or asteroid. The formalism was exact enough to allow mathematicians to predict the existence of the planet Neptune before it was observed.
It was only the orbit of the planet Mercury that Newton's Law of Gravitation seemed not to fully explain. Some astrophysicists predicted the existence of another planet (Vulcan) that would explain the discrepancies; however, despite some early indications, no such planet could be found. When Albert Einstein finally formulated his theory of general relativity (GR) he turned his attention to the problem of Mercury's orbit and found that his theory added a correction which could account for the discrepancy. This was the first time that Newton's Theory of Gravity had been shown to be less correct than an alternative.
Since then, and so far, general relativity has been acknowledged as the theory which best explains gravity. In GR, gravitation is not viewed as a force, but rather, objects moving freely in gravitational fields travel under their own inertia in straight lines through curved space-time – defined as the shortest space-time path between two space-time events. From the perspective of the object, all motion occurs as if there were no gravitation whatsoever. It is only when observing the motion in a global sense that the curvature of space-time can be observed and the force is inferred from the object's curved path. Thus, the straight line path in space-time is seen as a curved line in space, and it is called the ballistic trajectory of the object. For example, a basketball thrown from the ground moves in a parabola, as it is in a uniform gravitational field. Its space-time trajectory (when the extra ct dimension is added) is almost a straight line, slightly curved (with the radius of curvature of the order of few light-years). The time derivative of the changing momentum of the object is what we label as "gravitational force".
The electrostatic force was first described in 1784 by Coulomb as a force which existed intrinsically between two charges. The properties of the electrostatic force were that it varied as an inverse square law directed in the radial direction, was both attractive and repulsive (there was intrinsic polarity), was independent of the mass of the charged objects, and followed the law of superposition. Coulomb's Law unifies all these observations into one succinct statement.
Subsequent mathematicians and physicists found the construct of the electric field to be useful for determining the electrostatic force on an electric charge at any point in space. The electric field was based on using a hypothetical "test charge" anywhere in space and then using Coulomb's Law to determine the electrostatic force. Thus the electric field anywhere in space is defined as
Image:Force equation 21.png
where q is the magnitude of the hypothetical test charge.
Meanwhile, the Lorentz force of magnetism was discovered to exist between two electric currents. It has the same mathematical character as Coulomb's Law with the proviso that like currents attract and unlike currents repel. Similar to the electric field, the magnetic field can be used to determine the magnetic force on an electric current at any point in space. In this case, the magnitude of the magnetic field was determined to be
Image:Force equation 22.png
where I is the magnitude of the hypothetical test current and l is the length of hypothetical wire through which the test current flows. The magnetic field exerts a force on all magnets including, for example, those used in compasses. The fact that the Earth's magnetic field is aligned closely with the orientation of the Earth's axis causes compass magnets to become oriented because of the magnetic force pulling on the needle.
Through combining the definition of electric current as the time rate of change of electric charge, a rule of vector multiplication called Lorentz's Law describes the force on a charge moving in an magnetic field. The connection between electricity and magnetism allows for the description of a unified electromagnetic force that acts on a charge. This force can be written as a sum of the electrostatic force (due to the electric field) and the magnetic force (due to the magnetic field). Fully stated, this is the law:
Image:Force equation 23.png
where F is the electromagnetic force, q is the magnitude of the charge of the particle, E is the electric field, v is the velocity of the particle which is crossed with the magnetic field (B).
The origin of electric and magnetic fields would not be fully explained until 1864 when James Clerk Maxwell unified a number of earlier theories into a succinct set of four equations. These "Maxwell Equations" fully described the sources of the fields as being stationary and moving charges, and the interactions of the fields themselves. This led Maxwell to discover that electric and magnetic fields could be "self-generating" through a wave that traveled at a speed which he calculated to be the speed of light. This insight united the nascent fields of electromagnetic theory with optics and led directly to a complete description of the electromagnetic spectrum.
However, attempting to reconcile electromagnetic theory with two observations, the photoelectric effect, and the nonexistence of the ultraviolet catastrophe, proved troublesome. Through the work of leading theoretical physicists, a new theory of electromagnetism was developed using quantum mechanics. This final modification to electromagnetic theory ultimately led to quantum electrodynamics (or QED), which fully describes all electromagnetic phenomena as being mediated by wave particles known as photons. In QED, photons are the fundamental exchange particle which described all interactions relating to electromagnetism including the electromagnetic force.
It is a common misconception to ascribe the stiffness and rigidity of solid matter to the repulsion of like charges under the influence of the electromagnetic force. However, these characteristics actually result from the Pauli Exclusion Principle. Since electrons are fermions, they cannot occupy the same quantum mechanical state as other electrons. When the electrons in a material are densely packed together, there are not enough lower energy quantum mechanical states for them all, so some of them must be in higher energy states. This means that it takes energy to pack them together. While this effect is manifested macroscopically as a structural "force", it is technically only the result of the existence of a finite set of electron states.
There are two "nuclear forces" which today are usually described as interactions that take place in quantum theories of particle physics. The strong nuclear force is the force responsible for the structural integrity of atomic nuclei while the weak nuclear force is responsible for the decay of certain nucleons into leptons and other types of hadrons.
The strong force is today understood to represent the interactions between quarks and gluons as detailed by the theory of quantum chromodynamics (QCD). The strong force is the fundamental force mediated by gluons, acting upon quarks, antiquarks, and the gluons themselves. The strong interaction is the most powerful of the four fundamental forces.
The strong force only acts directly upon elementary particles. However, a residual of the force is observed between hadrons (the best known example being the force that acts between nucleons in atomic nuclei) as the nuclear force. Here the strong force acts indirectly, transmitted as gluons which form part of the virtual pi and rho mesons which classically transmit the nuclear force (see this topic for more). The failure of many searches for free quarks has shown that the elementary particles affected are not directly observable. This phenomenon is called colour confinement.
The weak force is due to the exchange of the heavy W and Z bosons. Its most familiar effect is beta decay (of neutrons in atomic nuclei) and the associated radioactivity. The word "weak" derives from the fact that the field strength is some 1013 times less than that of the strong force. Still, it is stronger than gravity over short distances. A consistent electroweak theory has also been developed which shows that electromagnetic forces and the weak force are indistinguishable at a temperatures in excess of approximately 1015 Kelvin. Such temperatures have been probed in modern particle accelerators and show the conditions of the universe in the early moments of the Big Bang.
Some forces are consequences of fundamental. In such situations, idealized models can be utilized to gain physical insight.
The normal force is the repulsive force of interaction between atoms at close contact. When their electron clouds overlap, Pauli repulsion (due to fermionic nature of electrons) follows resulting in the force which acts normal to the surface interface between two objects. The normal force, for example, is responsible for the structural integrity of tables and floors as well as being the force that responds whenever an external force pushes on a solid object. An example of the normal force in action is the impact force on an object crashing into an immobile surface.
Friction is a surface force that opposes relative motion. The frictional force is directly related to the normal force which acts to keep two solid objects separated at the point of contact. There are two broad classifications of frictional forces: static friction and kinetic friction.
The static friction force F will exactly oppose forces applied to an object parallel to a surface contact up to the limit specified by the coefficient of static friction (μsf) multiplied by the normal force (FN). In other words the magnitude of the static friction force satisfies the inequality:
Image:Force equation 24.png
The kinetic friction force (Fkf) is independent of both the forces applied and the movement of the object. Thus, the magnitude of the force equals:
Fkf = μkfFN
where μkf is the coefficient of kinetic friction. For most surface interfaces, the coefficient of kinetic friction is less than the coefficient of static friction.
Tension forces can be modeled using ideal strings which are massless, frictionless, unbreakable, and unstretchable. They can be combined with ideal pulleys which allow ideal strings to switch physical direction. Ideal strings transmit tension forces instantaneously in action-reaction pairs so that if two objects are connected by an ideal string, any force directed along the string by the first object is accompanied by a force directed along the string in the opposite direction by the second object. By connecting the same string multiple times to the same object through the use of a set-up that uses movable pulleys, the tension force on a load can be multiplied. For every string that acts on a load, another factor of the tension force in the string acts on the load. However, even though such machines allow for an increase in force, there is a corresponding increase in the length of string that must be displaced in order to move the load. These tandem effects result ultimately in the conservation of mechanical energy since the work done on the load is the same no matter how complicated the machine.
An elastic force acts to return a spring to its natural length. An ideal spring is taken to be massless, frictionless, unbreakable, and infinitely stretchable. Such springs exert forces that push when contracted, or pull when extended, in proportion to the displacement of the spring from its equilibrium position. This linear relationship was described by Robert Hooke in 1676, for whom Hooke's law is named. If Δx is the displacement, the force exerted by an ideal spring equals:
Image:Force equation 25.png
where k is the spring constant (or force constant), which is particular to the spring. The minus sign accounts for the tendency of the elastic force to act in opposition to the applied load.
Newton's laws and Newtonian mechanics in general were first developed to describe how forces affect idealized point particles rather than three-dimensional objects. However, in real life, matter has extended structure and forces that act on one part of an object might affect other parts of an object. For situations where lattice holding together the atoms in an object is able to flow, contract, expand, or otherwise change shape, the theories of continuum mechanics describe the way forces affect the material. For example, in extended fluids, differences in pressure result in forces being directed along the pressure gradients as follows:
Image:Force equation 26.png
where V is the volume of the object in the fluid and P is the scalar function that describes the pressure at all locations in space. Pressure gradients and differentials result in the buoyant force for fluids suspended in gravitational fields, winds in atmospheric science, and the lift associated with aerodynamics and flight.
A specific instance of such a force that is associated with dynamic pressure is fluid resistance: a body force that resists the motion of an object through a fluid due to viscosity. For so-called "Stokes' drag" the force is approximately proportional to the velocity, but opposite in direction:
Image:Force equation 27.png
b is a constant that depends on the properties of the fluid and the dimensions of the object (usually the cross-sectional area), and
v is the velocity of the object.
More formally, forces in continuum mechanics are fully described by a stress tensor with terms that are roughly defined as
Image:Force equation 28.png
where A is the relevant cross-sectional area for the volume for which the stress-tensor is being calculated. This formalism includes pressure terms associated with forces that act normal to the cross-sectional area (the matrix diagonals of the tensor) as well as shear terms associated with forces that act parallel to the cross-sectional area (the off-diagonal elements). The stress tensor accounts for forces that cause all deformations including also tensile stresses and compressions.
There are forces which are frame dependent, meaning that they appear due to the adoption of non-Newtonian (that is, non-inertial) reference frames. Such forces include the centrifugal force and the Coriolis force. These forces are considered fictitious because they do not exist in frames of reference that are not accelerating.
In general relativity, gravity becomes a fictitious force that arises in situations where spacetime deviates from a flat geometry. As an extension, Kaluza-Klein theory and string theory ascribe electromagnetism and the other fundamental forces respectively to the curvature of differently scaled dimensions, which would ultimately imply that all forces are fictitious.
Rotations and torque
Forces that cause extended objects to rotate are associated with torques. Mathematically, the torque on a particle is defined as the cross-product:
Image:Force equation 29.png
r is the particle's position vector relative to a pivot
F is the force acting on the particle.
Torque is the rotation equivalent of force in the same way that angle is the rotational equivalent for position, angular velocity for velocity, and angular momentum for momentum. All the formal treatments of Newton's Laws that applied to forces equivalently apply to torques. Thus, as a consequence of Newton's First Law of Motion, there exists rotational inertia that ensures that all bodies maintain their angular momentum unless acted upon by an unbalanced torque. Likewise, Newton's Second Law of Motion can be used to derive an alternative definition of torque:
Image:Force equation 30.png
I is the moment of inertia of the particle
α is the angular acceleration of the particle.
This provides a definition for the moment of inertia which is the rotational equivalent for mass. In more advanced treatments of mechanics, the moment of inertia acts as a tensor that, when properly analyzed, fully determines the characteristics of rotations including precession and nutation.
Equivalently, the differential form of Newton's Second Law provides an alternative definition of torque:
Image:Force equation 31.png
where L is the angular momentum of the particle.
Newton's Third Law of Motion requires that all objects exerting torques themselves experience equal and opposite torques, and therefore also directly implies the conservation of angular momentum for closed systems that experience rotations and revolutions through the action of internal torques.
For an object accelerating in circular motion, the unbalanced force acting on the object equals:
Image:Force equation 32.png
where m is the mass of the object, v is the velocity of the object and r is the distance to the center of the circular path and r is the unit vector pointing in the radial direction outwards from the center. This means that the unbalanced centripetal force felt by any object is always directed toward the center of the curving path. Such forces act perpendicular to the velocity vector associated with the motion of an object, and therefore do not change the speed of the object (magnitude of the velocity), but only the direction of the velocity vector. The unbalanced force that accelerates an object can be resolved into a component that is perpendicular to the path, and one that is tangential to the path. This yields both the tangential force which accelerates the object by either slowing it down or speeding it up and the radial (centripetal) force which changes its direction.
Forces can be used to define a number of physical concepts by integrating with respect to kinematic variables. For example, integrating with respect to time gives the definition of impulse:
Image:Force equation 33.png
which, by Newton's Second Law, must be equivalent to the change in momentum (yielding the Impulse momentum theorem).
Similarly, integrating with respect to position gives a definition for the work done by a force:
Image:Force equation 34.png
which is equivalent to changes in kinetic energy (yielding the work energy theorem).
Power P is the rate of change dW/dt of the work W, as the trajectory is extended by a position change dx in a time interval dt:
Image:Force equation 35.png
with Image:Force equation 36.png the velocity.
Instead of a force, often the mathematically related concept of a potential energy field can be used for convenience. For instance, the gravitational force acting upon an object can be seen as the action of the gravitational field that is present at the object's location. Restating mathematically the definition of energy (via the definition of work), a potential scalar field U(r) is defined as that field whose gradient is equal and opposite to the force produced at every point:
Image:Force equation 37.png
Forces can be classified as conservative or nonconservative. Conservative forces are equivalent to the gradient of a potential while non-conservative forces are not.
A conservative force that acts on a closed system has an associated mechanical work that allows energy to convert only between kinetic or potential forms. This means that for a closed system, the net mechanical energy is conserved whenever a conservative force acts on the system. The force, therefore, is related directly to the difference in potential energy between two different locations in space, and can be considered to be an artifact of the potential field in the same way that the direction and amount of a flow of water can be considered to be an artifact of the contour map of the elevation of an area.
Conservative forces include gravity, the electromagnetic force, and the spring force. Each of these forces has models which are dependent on a position often given as a radial vector r emanating from spherically symmetric potentials. Examples of this follow:
Image:Force equation 38.png
where G is the gravitational constant, and mn is the mass of object n.
For electrostatic forces:
Image:Force equation 39.png
where ε0 is electric permittivity of free space, and qn is the electric charge of object n.
For spring forces:
Image:Force equation 40.png
where k is the spring constant.
For certain physical scenarios, it is impossible to model forces as being due to gradient of potentials. This is often due to macrophysical considerations which yield forces as arising from a macroscopic statistical average of microstates. For example, friction is caused by the gradients of numerous electrostatic potentials between the atoms, but manifests as a force model which is independent of any macroscale position vector. Nonconservative forces other than friction include other contact forces, tension, compression, and drag. However, for any sufficiently detailed description, all these forces are the results of conservative ones since each of these macroscopic forces are the net results of the gradients of microscopic potentials.
The connection between macroscopic non-conservative forces and microscopic conservative forces is described by detailed treatment with statistical mechanics. In macroscopic closed systems, nonconservative forces act to change the internal energies of the system, and are often associated with the transfer of heat. According to the Second Law of Thermodynamics, nonconservative forces necessarily result in energy transformations within closed systems from ordered to more random conditions as entropy increases.
Units of measurement
The International_System_of_Units_(SI) unit of force is the newton (symbol N), which is the force required to accelerate a one kilogram mass at a rate of one meter per second squared, or kg·m·s-2. The corresponding CGS unit is the dyne, the force required to accelerate a one gram mass by one centimeter per second squared, or g·cm·s-2. A newton is thus equal to 100,000 dyne.
The gravitational foot-pound-second English unit of force is the pound-force (lbf), defined as the force exerted by gravity on a pound-mass in the standard gravitational field of 9.80665 m·s-2. The pound-force provides an alternative unit of mass: one slug is the mass that will accelerate by one foot per second squared when acted on by one pound-force.
An alternative unit of force in a different foot-pound-second system, the absolute fps system, is the poundal, defined as the force required to accelerate a one pound mass at a rate of one foot per second squared. The units of slug and poundal are designed to avoid a constant of proportionality in Newton's second law.
The pound-force has a metric counterpart, less commonly used than the newton: the kilogram-force (kgf) (sometimes kilopond), is the force exerted by standard gravity on one kilogram of mass. The kilogram-force leads to an alternate, but rarely used unit of mass: the metric slug (sometimes mug or hyl) is that mass which accelerates at 1 m·s-2 when subjected to a force of 1 kgf. The kilogram-force is not a part of the modern SI system, and is generally deprecated; however it still sees use for some purposes as expressing jet thrust, bicycle spoke tension, torque wrench settings and engine output torque. Other arcane units of force include the sthène which is equivalent to 1000 N and the kip
Units of Force
≡ 1 kg·m/s²
= 105 dyn
≈ 0.10197 kp
≈ 0.22481 lbf
≈ 7.2330 pdl
= 10−5 N
≡ 1 g·cm/s²
≈ 1.0197×10−6 kp
≈ 2.2481×10−6 lbf
≈ 7.2330×10−5 pdl
= 9.80665 N
= 980665 dyn
≡ gn·(1 kg)
≈ 2.2046 lbf
≈ 70.932 pdl
≈ 4.448222 N
≈ 444822 dyn
≈ 0.45359 kp
≡ gn·(1 lb)
≈ 32.174 pdl
≈ 0.138255 N
≈ 13825 dyn
≈ 0.014098 kp
≈ 0.031081 lbf
≡ 1 lb·ft/s²
- Physics Texts
- Lectures on Physics, R. P. Feynman, R. B. Leighton and M. Sands, Vol 1. Addison-Wesley (1963) http://www.amazon.com/dp/0-201-02116-1/?tag=encycofearth-20 ISBN: 0-201-02116-1
- An Introduction to Mechanics by Daniel Kleppner and Robert Kolenkow, McGraw-Hill (1973), p. 133–134 http://www.amazon.com/dp/0070350485/?tag=encycofearth-20 ISBN: 0070350485
- University Physics by Francis W. Sears, Mark W. Zemansky, Hugh D. Young, Addison-Wesley, Reading, MA (1982) http://www.amazon.com/dp/0-201-07199-1/?tag=encycofearth-20 ISBN: 0-201-07199-1
- Classical Mechanics, H.C. Corbell and Philip Stehle, p 28, Dover publications (1994)http://www.amazon.com/dp/0-486-68063-0/?tag=encycofearth-20 ISBN: 0-486-68063-0 
- “On the Concept of Force”, Walter Noll (2004)
- Physics, Sixth Edition by Jodn Cutnell and Kenneth W. Johnson, John Wiley & Sons Inc. (2004) http://www.amazon.com/dp/041-44895-8/?tag=encycofearth-20 ISBN: 041-44895-8
- Physics v. 1 by David Halliday, Robert Resnick and Kenneth S. Krane, John Wiley & Sons (2001 http://www.amazon.com/dp/0-471-32057-9/?tag=encycofearth-20 ISBN: 0-471-32057-9
- Encyclopedia of Physics, by Sybil Parker, McGraw-Hill (1993) p 443 http://www.amazon.com/dp/0-07-051400-3/?tag=encycofearth-20 ISBN: 0-07-051400-3
- Physics for Scientists and Engineers by Raymond A. Serway, Saunders College Publishing (2003) http://www.amazon.com/dp/0-534-40842-7/?tag=encycofearth-20 ISBN: 0-534-40842-7
- Physics for Scientists and Engineers: Mechanics, Oscillations and Waves, Thermodynamics 5th edition by Paul Tipler, W. H. Freeman (2004) http://www.amazon.com/dp/0-7167-0809-4/?tag=encycofearth-20 ISBN: 0-7167-0809-4
- Concepts of Physics Vol 1 (2004 Reprint) by H.C. Verma, Bharti Bhavan (2004) http://www.amazon.com/dp/81-7709-187-5/?tag=encycofearth-20 ISBN: 81-7709-187-5
- Space and Time: Inertial Frames, Robert DiSalle, Stanford Encyclopedia of Philosophy
- General Physics; mechanics and molecular physics by Lev Landau, A. I. Akhiezer, and A. M. Lifshitz, Translated by: J. B. Sykes, A. D. Petford, and C. L. Petford, Pergamon Press (1967) http://www.amazon.com/dp/0080033040/?tag=encycofearth-20 ISBN: 0080033040
- The Principia Mathematical Principles of Natural Philosophy by Isaac Newton, University of California Press (1999)(This is a recent translation into English by I. Bernard Cohen and Anne Whitman, with help from Julia Budenz.)http://www.amazon.com/dp/0-520-08817-4/?tag=encycofearth-20 ISBN: 0-520-08817-4
- Lesson 4: Newton's Third Law of Motion, Tom Henderson, The Physics Classroom
- Dynamics of translational motion, Dr. Nikitin (2007)
- Introduction to Free Body Diagrams, Physics Tutorial Menu, University of Guelph
- The Physics Classroom, Tom Henderson, The Physics Classroom and Mathsoft Engineering & Education, Inc. (2004)
- Static Equilibrium, Physics Static Equilibrium (forces and torques), University of the Virgin Islands
- Seminar: Visualizing Special Relativity, THE RELATIVISTIC RAYTRACER
- Four-Vectors (4-Vectors) of Special Relativity: A Study of Elegant Physics, John B. Wilson, The Science Realm: John's Virtual Sci-Tech Universe
- Pauli Exclusion Principle, R. Nave, HyperPhysics***** Quantum Physics
- Fermions & Bosons, The Particle Adventure
- A New Absolute Determination of the Acceleration due to Gravity at the National Physical Laboratory, A. H. Cook. Nature V. 208, p. 279 (1965)
- Perturbation Analysis, Regular and Singular, Thayer Watkins, Department of Economics, San José State University
- Recherches théoriques et expérimentales sur la force de torsion et sur l'élasticité des fils de metal, Charles Coulomb, Histoire de l’Académie Royale des Sciences p.229–269 (1784)br>
- Electricity and Magnetism, 3rd Ed. by William Duffin, McGraw-Hill (1980) http://www.amazon.com/dp/0-07-084111-X/?tag=encycofearth-20 ISBN: 0-07-084111-X
- Quantum-Chromodynamics: A Definition - Science Articles, Tab Stevens (2003)
- Tension Force, Non-Calculus Based Physics I
- Strings, pulleys, and inclines, Richard Fitzpatrick (2006)
- Elasticity, Periodic Motion, HyperPhysics, Georgia State University (2008)
- The Coriolis Force, Vincent Mallette, Publications in Science and Mathematics, Computing and the Humanities, Inwit Publishing, Inc. (1982-2008)
- Newton's Second Law for Rotation, HyperPhysics***** Mechanics ***** Rotation
- Engineering Mechanics, 12th edition by Russell C. Hibbeler, Pearson Prentice Hall (2010) http://www.amazon.com/dp/0-13-607791-9/?tag=encycofearth-20 ISBN: 0-13-607791-9
- The Foundation of the General Theory of Relativity, Albert Einstein , Annalen der Physik V.49 p. 769–822 (1916)
- Newton's third law of motion, Richard Fitzpatrick (2007)
- Centripetal Force, R. Nave, HyperPhysics***** Mechanics ***** Rotation
- Conservative force, Sunil Kumar Singh, Connexions (2007)
- Conservation of Energy, Doug Davis, General physics
- Metric Units in Engineering by Cornelius Wandmacher and Arnold Johnson, ASCE Publications (1995) http://www.amazon.com/dp/0784400709/?tag=encycofearth-20 ISBN: 0784400709
- Video lecture on Newton's three laws by Walter Lewin from MIT OpenCourseWare
- A Java simulation on vector addition of forces
- History Texts
- The Works of Archimedes, The unabridged work in PDF form, T.L. Heath,(1897).
- The Order of Nature in Aristotle's Physics: Place and the Elements by Helen Land(1998)
- Cosmology: Historical, Literary, Philosophical, Religious, and Scientific Perspectives by Norriss S. Hetherington, Garland Reference Library of the Humanities (1993)http://www.amazon.com/dp/0815310854/?tag=encycofearth-20 ISBN: 0815310854
- "Ibn S?n? and Buridan on the Motion of the Projectile", A. Sayili Espinoza, Annals of the New York Academy of Sciences 500 (1), pp. 477–482: (1987)
- "Abu'l-Barak?t al-Baghd?d? , Hibat Allah" by Shlomo Pines, Dictionary of Scientific Biography, Charles Scribner's Sons (1970) p. 26–28 http://www.amazon.com/dp/0684101149/?tag=encycofearth-20 ISBN: 0684101149
- "Avempace, Projectile Motion, and Impetus Theory", Abel B. Franco, Journal of the History of Ideas, 64(4), p. 521-546 .) (2003)
- "Ibn S?n? and Buridan on the Motion of the Projectile", A. Sayili (1987), Annals of the New York Academy of Sciences, 500 (1),
- "Islamic Conception Of Intellectual Life", Seyyed Hossein Nasr, in Philip P. Wiener (ed.), Dictionary of the History of Ideas, Vol. 2, p. 65, Charles Scribner's Sons, New York, 1973-1974.
- "Ibn al-Haytham or Alhazen", Nader El-Bizri, in Josef W. Meri (2006), "Medieval Islamic Civilization: An Encyclopaedia", Vol. II, p. 343-345, Routledge, New York, London.
- The History of Science from Augustine to Galileo by A. C. Crombie, Dover Publications (1996) ISBN 0486288501.
- "La dynamique d’Ibn Bajja", Shlomo Pines, in Mélanges Alexandre Koyré, I, 442-468 [462, 468], Paris (1964)
- Abu Arrayhan Muhammad ibn Ahmad al-Biruni, J J O'Connor and E F Robertson, The MacTutor History of Mathematics archive, (1999)
- "Galileo and Avempace: The Dynamics of the Leaning Tower Experiment (II)", Ernest A. Moody, Journal of the History of Ideas, 12(3), p. 375-422  (June 1951).
- Galileo At Work by Stillman Drake, Chicago: University of Chicago Press (1978).http://www.amazon.com/dp/0-226-16226-5/?tag=encycofearth-20 ISBN: 0-226-16226-5
- "An analysis of the historical development of ideas about motion and its implications for teaching", Fernando Espinoza, Physics Education, 40(2), p. 141. (2005)
- Sir Isaac Newton: The Universal Law of Gravitation, Astronomy 161 The Solar System
- Neptune's Discovery. The British Case for Co-Prediction., Nick Kollerstrom, University College London (2001)
Note: This article uses material from the Wikipedia article Force that was accessed on April 7, 2010. The Author(s) and Topic Editor(s) associated with this article have significantly modified the content derived from that original content or with content drawn from other sources. All such content has been reviewed and approved by those Author(s) and Topic Editor(s), and is subject to the same peer review process as other content in the EoE. The current version of the article differs significantly from the version that existed on the date of access. See the EoE’s Policy on the Use of Content from Wikipedia for more information.